Schedule A Service

 

 

In this article below you'll find additional sound news related to How to Install a Bathtub Yourself.

Mounting a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough project. If the old bathtub is conveniently available, the job can move rapidly; if you have to open a wall surface to eliminate the old bathtub and place the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. See to it you have actually qualified yourself for the job as well as fit trying it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to think about using one prior to you start. Opportunities are you might require a professional plumber to make tube links.
This write-up will assist you mount a new bathtub in your shower room if you have actually already purchased a brand-new bathtub and do not require to transform the setup of your previous water supply pipes.
Your devices and also product checklist ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic due to the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Installing the Bath tub

Making use of the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub till the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the supply of water and also inspect all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow outlet and also the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used at least once as this will certainly resolve it into its last placement.

 

 

Preparing for the Installment

Firstly, the supporting frame supplied with the bathroom must be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last setting.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I ran across that blog post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when browsing on the search engines. Do you know about someone else who is occupied with the topic? Why not share it. Thanks a lot for going through it.

Appointment